Thank you for visiting Bartle & Gibson. If you encounter any issues or have feedback to share, please email us at [email protected]. Your input is greatly appreciated!
TACO VM1816-HY2-4C200 0015E3-F4 3 SPEED HIGH EFFICIENCY CIRCULATOR PUMP WITH IFC
Product Details
Attributes
Features
Resources
Taco Comfort Solutions® ECM Circulator Pump With Integral Flow Check, 16 gpm Flow Rate, 18 ft Maximum Head, 44 W, 120 V, 0.54 A, 60 Hz, 125 psi Maximum Pressure, 4830 rpm Motor Speed Rating, 1/20 hp, 1 ph Phase, 36 to 230 deg F, Iron, 6 in H x 6-3/8 in W
Taco 0015e3is a variable speed, high-efficiency wet rotor circulator with an ECM permanent magnet motor. It's ideal for hydronic systems zoned with circulators or zone valves. With 3 easy settings, the 0015e3 delivers performance, reliability and ease of installation that made the 00 famous.
- 3 easy settings - low (5 ft head), medium (10 ft head), high (18 ft head), Install it, forget it
- BIO barrier protects pump from system contaminants
- SureStart automatic unblocking and air purging mode
- High-efficiency ECM motor uses up to 85% less electricity
- Double insulated, no ground wire required
- Whisper quiet operation
- Orange LED indicates 0015e3 running normally
- The white LED indicates that the innovative SureStart automatic unblocking and air purge is active, SureStart gives you the confidence that you'll never get a locked rotor with the 0015e3, install it, forget it
- Equipped with a cast iron casing and should be used for closed loop systems only
- Taco circulator pumps are for indoor use only
- Acceptable for use with water or maximum of 50% water/glycol solution
- Not for use on potable water or chilled water systems
- Composite stator housing, cartridge and impeller
- Ceramic shaft and thrust bearing
- Carbon bearings
- EPDM O-ring and gaskets
- ECM, permanent magnet, thermally protected type motor
- Dual electrical knockouts, 6 in stranded wire leads included for easy wiring
- For use with a Taco ZVC zone valve control or SR switching relay for ON/OFF operation
Product Details
Taco Comfort Solutions® ECM Circulator Pump With Integral Flow Check, 16 gpm Flow Rate, 18 ft Maximum Head, 44 W, 120 V, 0.54 A, 60 Hz, 125 psi Maximum Pressure, 4830 rpm Motor Speed Rating, 1/20 hp, 1 ph Phase, 36 to 230 deg F, Iron, 6 in H x 6-3/8 in W
Taco 0015e3is a variable speed, high-efficiency wet rotor circulator with an ECM permanent magnet motor. It's ideal for hydronic systems zoned with circulators or zone valves. With 3 easy settings, the 0015e3 delivers performance, reliability and ease of installation that made the 00 famous.
Attributes
Features
- 3 easy settings - low (5 ft head), medium (10 ft head), high (18 ft head), Install it, forget it
- BIO barrier protects pump from system contaminants
- SureStart automatic unblocking and air purging mode
- High-efficiency ECM motor uses up to 85% less electricity
- Double insulated, no ground wire required
- Whisper quiet operation
- Orange LED indicates 0015e3 running normally
- The white LED indicates that the innovative SureStart automatic unblocking and air purge is active, SureStart gives you the confidence that you'll never get a locked rotor with the 0015e3, install it, forget it
- Equipped with a cast iron casing and should be used for closed loop systems only
- Taco circulator pumps are for indoor use only
- Acceptable for use with water or maximum of 50% water/glycol solution
- Not for use on potable water or chilled water systems
- Composite stator housing, cartridge and impeller
- Ceramic shaft and thrust bearing
- Carbon bearings
- EPDM O-ring and gaskets
- ECM, permanent magnet, thermally protected type motor
- Dual electrical knockouts, 6 in stranded wire leads included for easy wiring
- For use with a Taco ZVC zone valve control or SR switching relay for ON/OFF operation